Merge pull request #664 from adafruit/TheKitty-patch-26

Create OpenSesame.ino

Author: TheKitty

Open_Sesame_SMS_Lock/OpenSesame/OpenSesame.ino

@@ -0,0 +1,188 @@
+#include <SoftwareSerial.h>
+#include "Adafruit_FONA.h"
+
+#define FONA_TX 3
+#define FONA_RX 4
+#define FONA_RST 5
+#define FONA_RI 2
+
+#define MOTOR_PWM A1
+#define MOTOR_1 A2
+#define MOTOR_2 A3
+
+#define LED 13
+
+#define OPEN true
+#define CLOSE false
+
+#define BUSYWAIT 5000  // milliseconds
+
+// this is a large buffer for replies
+char replybuffer[255];
+
+// or comment this out & use a hardware serial port like Serial1 (see below)
+SoftwareSerial fonaSS = SoftwareSerial(FONA_TX, FONA_RX);
+
+Adafruit_FONA fona = Adafruit_FONA(FONA_RST);
+
+uint8_t readline(char *buff, uint8_t maxbuff, uint16_t timeout = 0);
+
+boolean fonainit(void) {
+  Serial.println(F("Initializing....(May take 3 seconds)"));
+
+  digitalWrite(LED, HIGH);
+  delay(100);
+  digitalWrite(LED, LOW);
+  delay(100);
+  digitalWrite(LED, HIGH);
+  delay(100);
+  digitalWrite(LED, LOW);
+  delay(100);
+   
+  // make it slow so its easy to read!
+  fonaSS.begin(4800); // if you're using software serial
+  //Serial1.begin(4800); // if you're using hardware serial
+
+  // See if the FONA is responding
+  if (! fona.begin(fonaSS)) {           // can also try fona.begin(Serial1) 
+    Serial.println(F("Couldn't find FONA"));
+    return false;
+  }
+  Serial.println(F("FONA is OK"));
+  return true;
+  
+}
+
+void setup() {
+  while (!Serial);  // useful for Leonardo/Micro, remove in production!
+
+  // set LED output for debugging
+  pinMode(LED, OUTPUT);
+  
+  // set up motor pins, but turn them off
+  pinMode(MOTOR_1, OUTPUT);
+  digitalWrite(MOTOR_1, LOW);
+  pinMode(MOTOR_2, OUTPUT);
+  digitalWrite(MOTOR_2, LOW);  
+  pinMode(MOTOR_PWM, OUTPUT);
+  digitalWrite(MOTOR_PWM, LOW);  
+  
+  Serial.begin(115200);
+  Serial.println(F("FONA basic test"));
+
+  while (! fonainit()) {
+    delay(5000);
+  }
+  
+  // Print SIM card IMEI number.
+  char imei[15] = {0}; // MUST use a 16 character buffer for IMEI!
+  uint8_t imeiLen = fona.getIMEI(imei);
+  if (imeiLen > 0) {
+    Serial.print("SIM card IMEI: "); Serial.println(imei);
+  }
+  
+  pinMode(FONA_RI, INPUT);
+  digitalWrite(FONA_RI, HIGH); // turn on pullup on RI
+  // turn on RI pin change on incoming SMS!
+  fona.sendCheckReply(F("AT+CFGRI=1"), F("OK"));
+}
+
+int8_t lastsmsnum = 0;
+
+void loop() {
+   digitalWrite(LED, HIGH);
+   delay(100);
+   digitalWrite(LED, LOW);
+       
+  while (fona.getNetworkStatus() != 1) {
+    Serial.println("Waiting for cell connection");
+    delay(2000);
+  }
+  
+  // this is a 'busy wait' loop, we check if the interrupt
+  // pin went low, and after BUSYWAIT milliseconds break out to check
+  // manually for SMS's and connection status
+  // This would be a good place to 'sleep'
+  for (uint16_t i=0; i<BUSYWAIT; i++) {
+     if (! digitalRead(FONA_RI)) {
+        // RI pin went low, SMS received?
+        Serial.println(F("RI went low"));
+        break;
+     } 
+     delay(1);
+  }
+  
+  int8_t smsnum = fona.getNumSMS();
+  if (smsnum < 0) {
+    Serial.println(F("Could not read # SMS"));
+    return;
+  } else {
+    Serial.print(smsnum); 
+    Serial.println(F(" SMS's on SIM card!"));
+  }
+  
+  if (smsnum == 0) return;
+
+  // there's an SMS!
+  uint8_t n = 1; 
+  while (true) {
+     uint16_t smslen;
+     char sender[25];
+     
+     Serial.print(F("\n\rReading SMS #")); Serial.println(n);
+     uint8_t len = fona.readSMS(n, replybuffer, 250, &smslen); // pass in buffer and max len!
+     // if the length is zero, its a special case where the index number is higher
+     // so increase the max we'll look at!
+     if (len == 0) {
+        Serial.println(F("[empty slot]"));
+        n++;
+        continue;
+     }
+     if (! fona.getSMSSender(n, sender, sizeof(sender))) {
+       // failed to get the sender?
+       sender[0] = 0;
+     }
+     
+     Serial.print(F("***** SMS #")); Serial.print(n);
+     Serial.print(" ("); Serial.print(len); Serial.println(F(") bytes *****"));
+     Serial.println(replybuffer);
+     Serial.print(F("From: ")); Serial.println(sender);
+     Serial.println(F("*****"));
+     
+     if (strcasecmp(replybuffer, "open sesame") == 0) {
+       // open the door!
+       digitalWrite(LED, HIGH);
+       moveMotor(OPEN, 800);
+       digitalWrite(LED, LOW);
+     }
+     if (strcasecmp(replybuffer, "close cadabra") == 0) {
+       // close the door!
+       digitalWrite(LED, HIGH);
+       moveMotor(CLOSE, 800);
+       digitalWrite(LED, LOW);
+     }
+     
+     delay(3000);
+     break;
+  }  
+  fona.deleteSMS(n);
+ 
+  delay(1000); 
+}
+
+
+void moveMotor(boolean direction, uint16_t t) {
+  digitalWrite(MOTOR_PWM, HIGH);   // enable motor
+  if (direction) {
+    digitalWrite(MOTOR_1, HIGH);
+    digitalWrite(MOTOR_2, LOW);
+  } else {
+    digitalWrite(MOTOR_2, HIGH);
+    digitalWrite(MOTOR_1, LOW);  
+  }
+  delay(t);
+  digitalWrite(MOTOR_1, LOW);
+  digitalWrite(MOTOR_2, LOW);
+
+  digitalWrite(MOTOR_PWM, LOW);    // disable motor
+}