variant.cpp

/*
 *******************************************************************************
 * Copyright (c) 2017, STMicroelectronics
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 * 3. Neither the name of STMicroelectronics nor the names of its contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *******************************************************************************
 */

#include "pins_arduino.h"

#ifdef __cplusplus
extern "C" {
#endif

// Pin number
// This array allows to wrap Arduino pin number(Dx or x)
// to STM32 PinName (PX_n)
const PinName digitalPin[] = {
  // USB connector on the top, MCU side
  // Left Side
  PA_0,  //D0
  PA_1,  //D1
  PA_2,  //D2  - TX
  PA_3,  //D3  - RX
  PA_4,  //D4  - LED
  // Right side
  PA_5,  //D5  - SCK
  PA_6,  //D6  - MISO
  PA_7,  //D7  - MOSI
  PB_1,  //D8  - SS
  PA_9,  //D9  - SCL (TX UART Header)
  PA_10, //D10 - SDA (RX UART Header)
  PA_13, //D11 - SWDIO
  PA_14, //D12 - SWCLK
  // These two are only available on boards without a crystal:
  PF_0,
  PF_1,
  // Duplicated pins in order to be aligned with PinMap_ADC
  // A0 have to be greater than NUM_ANALOG_INPUTS
  PA_0,  //D15/A0 ~ D0
  PA_1,  //D16/A1 ~ D1
  PA_2,  //D17/A2 ~ D2
  PA_3,  //D18/A3 ~ D3
  PA_4,  //D19/A4 ~ D4
  PA_5,  //D20/A5 ~ D5
  PA_6,  //D21/A6 ~ D6
  PA_7,  //D22/A7 ~ D7
  PB_1   //D23/A8 ~ D8
};

#ifdef __cplusplus
}
#endif

// ----------------------------------------------------------------------------

#ifdef __cplusplus
extern "C" {
#endif

/**
  * @brief  System Clock Configuration
  * @param  None
  * @retval None
  */
WEAK void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;

  /* Initializes the CPU, AHB and APB busses clocks */
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
#ifdef ARDUINO_DEMO_F030F4_HSI
  /* Internal HSI, 48MHz system clock */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL12;
  RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
#else
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI14 | RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.HSI14State = RCC_HSI14_ON;
  RCC_OscInitStruct.HSI14CalibrationValue = 16;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
#ifdef ARDUINO_DEMO_F030F4_16M
  RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2;
#else
  RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
#endif
#endif
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
    _Error_Handler(__FILE__, __LINE__);
  }

  /* Initializes the CPU, AHB and APB busses clocks */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
                                | RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) {
    _Error_Handler(__FILE__, __LINE__);
  }
}

#ifdef __cplusplus
}
#endif