Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
2 changes: 2 additions & 0 deletions docs/Ropener-User-Guide.md
Original file line number Diff line number Diff line change
Expand Up @@ -336,6 +336,7 @@ Every other reading and setting on the web page has its own topic under the same
| No setup hotspot appears | Wait a full minute after power-on. If it already joined a network, hold Button 3 for 3–10 seconds to reset Wi-Fi and try again. |
| Open/Close are reversed | Set the “Motor Direction” setting to **Reversed**. |
| Position is wrong / drifted | Run homing (Section 5) to recalibrate. |
| “Update Firmware (GitHub)” didn't update | Check **Firmware Update** under Diagnostics: it shows the progress or why the update failed (for example no internet, or GitHub's security certificate couldn't be verified). A failed update never changes the firmware the device is running — fix the cause and press the button again. |
| Curtain closes a little shorter every cycle | First check **Driver Temperature** and **Driver Shutdowns** under Diagnostics. If Driver Temperature ever shows Hot or Overheated, or Driver Shutdowns is above 0, the motor driver is cutting out on long runs: **lower** the Motor Current (IRUN) and keep Speed at Medium. Otherwise the rope may be slipping. In either case, Close Overtravel (Section 10) makes up the difference on every close. |
| Schedule fires at the wrong time | Check the Timezone value (Section 7/8) and that the device has internet for time sync. |
| Schedule doesn't run | Confirm “Schedule Enabled” is ON and that Open/Close times are set. |
Expand Down Expand Up @@ -371,6 +372,7 @@ Every other reading and setting on the web page has its own topic under the same
| SG_RESULT / TSTEP | Live readings used when tuning homing. |
| Driver Temperature | Motor driver health: OK, Hot, Overheated, or “Overheated earlier – re-home” (Diagnostics). |
| Driver Shutdowns | How many times the motor driver has shut off since the last restart (Diagnostics). Each one loses position. |
| Firmware Update | Progress of the last “Update Firmware (GitHub)” press, or why it failed (Diagnostics). |
| MQTT Broker / Port / Username / Password / Enabled | Connect to an MQTT broker (Section 11). |
| MQTT Status | Off, Connecting…, Connected with the topic prefix, or “press Restart to Apply” after a change. |
| Restart to Apply | Restarts the device so changed MQTT settings take effect. |
Expand Down
2 changes: 1 addition & 1 deletion firmware/README.md
Original file line number Diff line number Diff line change
Expand Up @@ -50,5 +50,5 @@ Hold-to-run is the child- and elderly-friendly mode: the curtain only moves whil

Two ways to update:

- **Over the air, from the device:** open the settings page and, under Diagnostics, press **"Update Firmware (GitHub)"**. The device downloads the latest release for its model straight from GitHub, flashes itself, and reboots — no computer needed. (Requires an internet connection.)
- **Over the air, from the device:** open the settings page and, under Diagnostics, press **"Update Firmware (GitHub)"**. The device downloads the latest release for its model straight from GitHub, flashes itself, and reboots — no computer needed. (Requires an internet connection.) **Firmware Update** (also under Diagnostics) shows the progress, or why an update failed; a failed update leaves the current firmware running.
- **Manually:** download the `*.ota.bin` (for a device already on your network) or `*.factory.bin` (for a fresh USB flash) for your model from the [latest release](https://github.com/Valar-Systems/Ropener/releases/latest) and upload it as before.
4 changes: 2 additions & 2 deletions firmware/VAL3000/Ropener-VAL3000.yml
Original file line number Diff line number Diff line change
Expand Up @@ -32,12 +32,12 @@ esphome:
packages:
valar_core:
url: https://github.com/Valar-Systems/valar-motion
ref: v0.2.0
ref: v0.3.1
files: [common/valar-core.yaml]
refresh: 1d
scheduling:
url: https://github.com/Valar-Systems/valar-motion
ref: v0.2.0
ref: v0.3.1
files: [common/scheduling.yaml]
refresh: 1d
product: !include ../common/ropener-product.yaml
4 changes: 2 additions & 2 deletions firmware/VAL3100/Ropener-VAL3100.yml
Original file line number Diff line number Diff line change
Expand Up @@ -33,12 +33,12 @@ esphome:
packages:
valar_core:
url: https://github.com/Valar-Systems/valar-motion
ref: v0.2.0
ref: v0.3.1
files: [common/valar-core.yaml]
refresh: 1d
scheduling:
url: https://github.com/Valar-Systems/valar-motion
ref: v0.2.0
ref: v0.3.1
files: [common/scheduling.yaml]
refresh: 1d
product: !include ../common/ropener-product.yaml
Expand Down
Loading